备件储存保养标准.doc

永锋集团有限公司备件储存保养标准目录第一章电动机储存及在线备用保养标准·····················4一、储存环境要求········································4二、储存要求············································4三、储存及在线备用期间的保养要求:·······················5附件一大型电动机转子转动方法···························6第二章离心风机储存及在线备用保养标准···················8一、储存环境要求········································8二、储存要求············································8三、储存及在线备用期间的保养要求:·······················8附件二离心风机叶轮转动方法····························9第三章减速机储存及在线备用保养标准····················11一、储存环境要求·······································11二、储存要求···········································11三、在线储存或备用期间的保养要求:······················11第四章轴及齿轮储存保养标准····························13一、储存环境要求·······································13二、储存要求···········································13三、储存期间的保养要求:································13第五章变频器储存及在线备用保养标准·····················14一、储存环境要求········································14二、储存要求············································14三、储存及在线备用期间的保养要求:·······················14第六章电子类备件储存保养标准··························15一、储存环境要求·······································15二、储存要求···········································15三、储存期间的保养要求:································15第七章考核·············································15第一章电动机储存及在线备用保养标准一、储存环境要求:1、不允许有白蚁、盐雾、腐蚀性气体、危险性气体及过多类尘。2、环境相对湿度不大于70%,但对于TH型电动机相对湿度可不大于95%。3、储存地点应该通风良好,但不允许室外储存。户外型(包括露天)也不例外。二、库存储存要求:1、电动机储存时,应拆箱清除尘污,并将轴伸、集电环、进出水法兰等露出之表面擦净,清除原来涂上的临时性涂料及表面潮气和可能存在的表面锈渍等。用清洗液将油渍擦干净,表面仍有锈渍时,则可用00号细砂布加油轻轻擦光,再用防锈油或临时性涂封材料将表面重新涂封。2、储存时电机应进行全面密封处理,以防异物进入。3、禁止将电动机与磁性件及具有化学腐蚀性酸、碱及蓄电池等物品存放在一起。4、对绕线型电机,为了防止集电环的工作表面形成斑点,在集电环与电刷间应垫以绝缘板。5、使用过的电动机,如停止使用并打算储存起来的话,必须将电动机全部拆开清理干净,电动机组装前,轴承清理注上新的润滑脂,对于水—空冷却型电动机,还必须将冷却器里面的水和污物清理干净,并将轴伸、集电环、进出水法兰等按1条的要求清理干净,滑动轴承必须将轴承里的润滑油放干净,轴颈和轴瓦用油脂涂封,以免锈蚀。6、经过检查和清理的电动机,必须放入包装箱内进行储存,无包装箱的应进行包裹或遮盖。装箱的地点应该清洁,无过多灰尘、无盐雾、无腐蚀性和危险性气体。检查和清理电动机的地点也应符合这些要求,以免损坏绝缘和裸露之导电部分。三、储存及在线备用期间的保养要求:1、电动机(包括整体包装的电动机)在储存期间,应每三个月转动转子(具体转动方法见附件一),尤其对采用滑动轴承的电机,可防止因静压变形过久而造成的巴氏合金变形。2、储存的电动机每隔半年应检查一次,检查临时性涂封是否变质,是