备件储存保养标准.docx

永锋集团有限公司备件储存保养标准备件储存保养标准 2/ 18 目录第一章电动机储存及在线备用保养标准····················· 4一、储存环境要求········································ 4二、储存要求············································ 4三、储存及在线备用期间的保养要求:······················· 5 附件一大型电动机转子转动方法··························· 6 第二章离心风机储存及在线备用保养标准··················· 8一、储存环境要求········································ 8二、储存要求············································ 8三、储存及在线备用期间的保养要求:······················· 8 附件二离心风机叶轮转动方法···························· 9备件储存保养标准 3/ 18 第三章减速机储存及在线备用保养标准···················· 11 一、储存环境要求······································· 11 二、储存要求··········································· 11 三、在线储存或备用期间的保养要求:······················ 11 第四章轴及齿轮储存保养标准···························· 13 一、储存环境要求······································· 13 二、储存要求··········································· 13 三、储存期间的保养要求:································ 13 第五章变频器储存及在线备用保养标准····················· 14 一、储存环境要求········································ 14 二、储存要求············································ 14备件储存保养标准 4/ 18 三、储存及在线备用期间的保养要求:······················· 14 第六章电子类备件储存保养标准·························· 15一、储存环境要求······································· 15 二、储存要求··········································· 15 三、储存期间的保养要求:································ 15 第七章考核············································· 15备件储存保养标准 5/ 18 第一章电动机储存及在线备用保养标准一、储存环境要求: 1 、不允许有白蚁、盐雾、腐蚀性气体、危险性气体及过多类尘。 2、环境相对湿度不大于 70% , 但对于 TH 型电动机相对湿度可不大于 95% 。 3、储存地点应该通风良好, 但不允许室外储存。户外型( 包括露天) 也不例外。二、库存储存要求: 1 、电动机储存时,应拆箱清除尘污,并将轴伸、集电环、进出水法兰等露出之表面擦净, 清除原来涂上的临时性涂料及表面潮气和可能存在的表面锈渍等。用清洗液将油渍擦干净, 表面仍有锈渍时, 则可用 00 号细砂布加油轻轻擦光,再用防锈油或临时性涂封材料将表面重新涂封。 2 、储存时电机应进行全面密封处理,以防异物进入。 3 、禁止将电动机与磁性件及具有化学腐蚀性酸、碱及蓄电池等物品存放在一起。 4 、对绕线型电机,为了防止集电环的工作表面形成斑点,在集电环与电刷间应垫以绝缘板。 5 、使用过的电动机,如停止使用并打算储存起来的话,必须将电动备件储存保养标准 6/ 18 机全部拆开清理干净,电动机组装前,轴承清理注上新的润滑脂,对于水—空冷却型电动机,还必须将冷却器里面的水和污物清理干净, 并将轴伸、集电环、进出水法兰等按 1 条的要求清理干净, 滑动轴承必须将轴承里的润滑油放干净,轴颈和轴瓦用油脂涂封,以免锈蚀。 6 、经过检查和清理的电动机,必须放入包装箱内进行储存,无包装箱的应进行包裹或遮盖。装箱的地点应该清洁, 无过多灰尘、无盐雾、无腐蚀性和危险性气体。检查和清理电动