备件储存保养标准.doc

永锋集团
备件储存保养标准
目录
第一章电动机储存及在线备用保养标准·····················4
一、储存环境要求········································4
二、储存要求············································4
三、储存及在线备用期间的保养要求：·······················5
附件一大型电动机转子转动方法···························6
第二章离心风机储存及在线备用保养标准···················8
一、储存环境要求········································8
二、储存要求············································8
三、储存及在线备用期间的保养要求：·······················8
附件二离心风机叶轮转动方法····························9
第三章减速机储存及在线备用保养标准····················11
一、储存环境要求·······································11
二、储存要求···········································11
三、在线储存或备用期间的保养要求：······················11
第四章轴及齿轮储存保养标准····························13
一、储存环境要求·······································13
二、储存要求···········································
13
三、储存期间的保养要求：································13
第五章变频器储存及在线备用保养标准·····················14
一、储存环境要求········································14
二、储存要求············································14
三、储存及在线备用期间的保养要求：·······················14
第六章电子类备件储存保养标准··························15一、储存环境要求·······································15
二、储存要求···········································15
三、储存期间的保养要求：································15
第七章考核·············································15
第一章电动机储存及在线备用
保养标准
一、储存环境要求：
1、不允许有白蚁、盐雾、腐蚀性气体、危险性气体及过多类尘。
2、环境相对湿度不大于70%，但对于TH型电动机相对湿度可不大于95%。
3、储存地点应该通风良好，但不允许室外储存。户外型（包括露天）也不例外。
二、库存储存要求：
1、电动机储存时，应拆箱清除尘污，并将轴伸、集电环、进出水法兰等露出之表面擦净，清除原来涂上的临时性涂料及表面潮气和可能存在的表面锈渍等。用清洗液将油渍擦干净，表面仍有锈渍时，则可用00号细砂布加油轻轻擦光，再用防锈油或临时性涂封材料将表面重新涂封。
2、储存时电机应进行全面密封处理，以防异物进入。
3、禁止将电动机与磁性件及具有化学腐蚀性酸、碱及蓄电池等物品存放在一起。
4、对绕线型电机，为了防止集电环的工作表面形成斑点，在集电环与电刷间应垫以绝缘板。
5、使用过的电动机，如停止使用并打算储存起来的话，必须将电动机全部拆开清理干净，电动机组装前，轴承清理注上新的润滑脂，对于水
—空冷却型电动机，还必须将冷却器里面的水和污物清理干净，并将轴伸、集电环、进出水法兰等按1条的要求清理干净，滑动轴承必须将轴承里的润滑油放干净，轴颈和轴瓦用油脂涂封，以免锈蚀。
6、经过检查和清理的电动机，必须放入包装箱进行储存，无包装箱的应进行包裹或遮盖。装箱的地点应该清洁，无过多灰尘、无盐雾、无腐蚀性和危险性气体。检查和清理电动机的地点也应符合这些要求，以免损坏绝缘和裸露之导电部分。