组播路由协议配置(华为).doc常用组播路由协议配置方法1IGMP协议配置1*:#将VLAN接口VLAN-0/1加入组播组#。[Quidway-Vlan-interface10]igmphost-.2控制某个接口下主机能够加入的组播组igmpgroup-policyacl-number[1|2|port{interface_typeinterface_num|interface_name}[to{interface_typeinterface_num|interface_name}]]【例如】#配置访问控制列表acl2000[Quidway]aclnumber2000[Quidway-acl-basic-2000]#指定VLAN-interface10上满足acl2000中规定的范组,指定组的IGMP版本为2。[Quidway・Vlan-interfacelO]igmpgroup-policy20002IGMP版本切换igmpversion{1|2}#在VLAN接口VLAN-interface10上运行IGMP版本1。[Quidway-Vlan-interface10]igmpversion1IGMP查询间隔时间:默认60sigmptimerqueryseconds#将VLAN-interface2接口上的主机成员杏询报文发送间隔设置为150秒。[Quidway-Vian-interface2]igmptimerquery150IGMP查询超时时间:默认为2倍的查询间隔时间igmptimerother-querier-present#配置Querier的存活时间为300秒[Quidway-Vlan-interface10]igmptimerother-querier-present3001-L6IGMP査询最大响应时间:默认为10sigmpmax-response-timeseconds#配置主机成员查询报文中包含的最大响应时间为8秒。[Quidway-Vlan-interface10]igmpmax-response-time81,-3,在RouterA和RouterB的接口上启动IGMP和PIM-DM«在末梢网络路由器RouterB上,2/0/1/0/0o(有关PIM-DM协议配置请参见下一章。)(1)配置路由器RouterB:#启动组播。[RouterB]multicastrouting-enable#2/0/0>1/0/0上启动IGMP。[RouterB]2/0/0[RouterB-2/0/0]igmpenable[RouterB-2/0/0]1/0/0[RouterB-1/0/0]igmpenable[RouterB-1/0/0]quit#1/0/2/0/0的IGMPProxy代理接口。[RouterB]2/0/0[RouterB-2/0/0]l/0/0(2)配置路由器RouterA:#启动组播。[RouterA]multicastrouting-enable#2/0/0上启动IGMP、PIM-DMo[RouterA]2/0/0[RouterA-2/0/0]igmpenable[RouterA-2/0/0]-snooping{enable|disable}#在VLAN100上使能IGMPSnoopingo[Quidway]igmp-:[Quidway]vlan100[Quidway-vlanl00]igmp--snoopinghost-aging-timeseconds#把老化时间设置为300秒。[Quidway]igmp-snoopinghost-aging--snoopingrouter-aging-timeseconds#设置IGMPSnooping路由器端口老化时间为300秒。[Quidway]igmp-snoopingrouter-aging--snoopingmax-response-timeseconds#设置IGMPSnooping报文的响应时间为12秒。[Quidway]igmp-snoopingmax-response-time1
组播路由协议配置(华为) 来自淘豆网www.taodocs.com转载请标明出处.